Exactly How to Install a Bathtub
Exactly How to Install a Bathtub
Blog Article
What're your opinions with regards to How to Install a Bathtub Yourself?
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as in some cases, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably difficult project. If the old bathtub is easily easily accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub and position the new tub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have qualified yourself for the task and also fit attempting it. Rather than hiring a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This article will certainly assist you mount a brand-new bathtub in your shower room if you have currently bought a new bathtub and don't require to change the plan of your previous water supply pipes.
Your devices and product list should make up the following:
Planning for the Installation
To start with, the supporting framework provided with the bath must be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet with the hole in the bathroom. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its final setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe links on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, put the bath tub in the needed setting. The wooden boards are useful in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four tiny factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the bathtub until the spirit level checks out level.
To set up taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if necessary. Load the tub and additionally examine the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling and sealing around the bathtub needs to wait until the tub has actually been utilized at the very least once as this will certainly resolve it right into its final placement.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making certain that the washing machines remain in place between the tap and also the sink. Protect the faucet in position with the manufacturer given backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind should be linked to the faucet finishes first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a stiff seal, triggering the water to permeate the wall in between the bathroom and also the tiling, leading to complications with dampness as well as possible leakages to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise quickly available on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that piece on Installing A Bathtub while doing a lookup on the internet. You should set aside a second to promote this blog posting if you liked it. Thanks for taking the time to read it.
Visit Our Site
Report this page